Waterbath WNE 7 - 45WPE 45OilbathONE 7 - 45Operating instructiOns
EXCELLENT page 104 Bath construction and operationThe heating positioned on three sides around the tank ensures a natural water circulation of the
EXCELLENTpage 114.2 Switching onThe bath is switched on by pressing the push/turn controland can be operated in connection with the SET-key.Bath swit
EXCELLENT page 124.3.1 Temperature setpointThe bath starts to heat up immediately to the set temperature.Adjustment range:waterbaths: 10°C to 95°C o
EXCELLENTpage 134.3.3 Hold time of the setpoint temperatureThe bath switches off the heating after the end of the selected hold time. In this case th
EXCELLENT page 144.3.5 Circulating pump (WPE 45 only)Operation of a circulating pump can improve the temperature distribution inside the waterbath. T
EXCELLENTpage 154.3.6 Temperature monitor(see also sections 4.3.8.2 and 7)Adjustment range:up to 10°C above nominal temperatureSetting and indication
EXCELLENT page 164.3.8.1 CalibrationCustomer calibration of the bath on the controller using a self-selected calibration temperature. A positive or n
EXCELLENTpage 174.3.8.2 Selection of temperature monitor (waterbaths only)Setting:2 or 3.1Rotate the push/turn control until flashes.With the SET
EXCELLENT page 186 Monitoring the programme sequenceBath does not heat upDuring the delayed switch-on the symbol flashes and the display alternates
EXCELLENTpage 197 Temperature monitor and protection devicesThe monitor temperature is measured with a separate Pt100 temperature sensor inside the
EXCELLENT page 2
EXCELLENT page 207.2.1 Adjustable temperature monitor ( TWW) Protection Class 3.1 to DIN 12880If the manually set monitor temperatur is exceeded, t
EXCELLENTpage 218 Use of the cover (special equipment)Gable cover The gable cover (may be ordered as already mounted special equipment) should always
EXCELLENT page 2210 Cooling system (special equipment)If the waterbath is fitted with a cooling device for quicker cooling of the bath liquid, the “w
EXCELLENTpage 2312 Check list for fault rectificationIn case of a malfunction contact an authorized service station for Memmert equipment or please
EXCELLENT page 2415 CE Conformity of DeclarationEC Declaration of Conformity Manufacturer´s name and address: MEMMERT GmbH + Co. KG Äußere Ritters
EXCELLENTpage 25Standard units are safety-approved and bear the test marks:This product is subject to the Directive 2002/96/EC by the European Parliam
EXCELLENT page 2617 IndexAaddress 25alarm symbol 19, 20ambient conditions 5ambient temperature 23autodiagnostic system 6Bbath construction 10boi
EXCELLENTpage 27
Memmert gmbH + co. Kg | Postfach 1720 | D-91107 Schwabach | Tel. +49 (0) 9122 / 925 - 0 | Fax +49 (0) 9122 / 145 85 | E-Mail: [email protected] | www.
EXCELLENTpage 31 General notes and safety notes ...
EXCELLENT page 41 General notes and safety notesYou have purchased a technically fully proven product which has been produced in Germany with the use
EXCELLENTpage 52 Technical dataModel 7 1014222945Volume [liter] 7 10 14 22 29 45Usable bath length A [mm] 240 350 350 350 590 590Usable bath width B
EXCELLENT page 62.1 Material qualityMemmert is using stainless steel ( Mat.Ref. 1.4301) for the external casing as well as for the interior, an outst
EXCELLENTpage 72.5 Standard equipment• Electronic fuzzy-supported PID process controller with delayed programme start and programmable hold time.
EXCELLENT page 83.1 Initial start-upWhen the bath is started up for the first time, it should be supervised continuously until steady conditions have
EXCELLENTpage 93.3 Installation - oilbathsMainsconnectionThe mains connection cable must be placed away from any hot surface. FillingIMPORTANT! The
Commentaires sur ces manuels